FAAC Gate Installation Nationwide

FAAC Gate Installation in Cerritos: What to Know First

FAAC gate installation in Cerritos typically runs $1,900 to $6,800 depending on gate size, operator model, and whether we’re automating an existing gate or hanging a new one. As an independent FAAC service provider, Ironworks Gate Co. installs and programs the full FAAC lineup, from the residential 400 Series swing operators to the heavier 770 and 844 sliding-gate workhorses, and most jobs are completed in a single day. The price you’re quoted is the price you pay, settled before we turn a single bolt.

Call (747) 298-3226

This page is for Cerritos homeowners who already own FAAC equipment, or have been quoted one, and want the installation done by someone who actually understands the brand’s quirks. If you’ve got a FAAC 391, 400, 770, 844, or an older model still doing its job, call (747) 298-3226. Victor Salinas, our owner, grew up in Cerritos and has been working on these gates for the better part of four decades.

How FAAC Products Fail - and How We Fix Them

FAAC builds solid operators, but every line has its known trouble spots. Here’s what we see on Cerritos driveways, and what we do about it.

• FAAC 400 Series (swing gates): capacitor failure after 5-7 years. The 400 is common on single and double swing gates throughout Cerritos, and the first thing to go is usually the motor start capacitor. Symptoms look like a dead board: the gate hums but doesn’t move, or moves a few inches and stops. We test the capacitor before replacing anything else, because a $40 part shouldn’t turn into a $700 board replacement. When we install a 400 Series, we always check capacitor age and note it on the job sheet.
• FAAC 770 and 844 (sliding gates): limit switch drift from debris. Cerritos wind blows fine dust and leaf litter into the track channel of sliding gates, and FAAC limit switches don’t love it. The gate stops six inches short of closed, or overtravels and slams the stop. During installation we set limit switch cams with a wider tolerance than factory spec and seal the housing better than the original install. It’s a small thing that prevents a callback.
• FAAC control boards (all residential lines): solder joints crack from vibration. California gate operators cycle hundreds of times a month in family homes. Over years, vibration cracks solder joints on FAAC board connectors, especially where the transformer ties in. We see intermittent failures that baffle homeowners: works fine for a week, then dead. On installs, we mount boards on new isolation dampers, and if we’re splicing wiring, we solder and heat-shrink rather than using crimp connectors alone.
• FAAC hydraulic operators (older 391, 400 hydraulic): fluid leaks at the ram seals. FAAC’s hydraulic units are reliable for a long time, but when the ram seals go, oil weeps down the post, and the gate moves slower and slower. Some shops quote a whole new operator. We replace the seal kit and re-bleed the system, which on a FAAC is straightforward work if you’ve done it before. We’ve done it many times.
• FAAC photocell alignment (all lines): sun angle and heat expansion. Cerritos summers do two things to photocells: direct afternoon sun hits the receiver, and gate steel expands just enough to nudge a misaligned beam. The gate refuses to close, or reverses for no visible reason. We replace older FAAC photocells with newer wide-angle models during installation and aim them with the gate in the afternoon sun position, not the morning.

Our FAAC Gate Installation Process

When you call Ironworks Gate Co. for a FAAC installation in Cerritos, here’s what happens.

1. 1
   Call and assessment. You reach a live person, day or night. We ask what FAAC model you have, what the gate weighs, and what it’s doing. If you don’t know the model, the serial plate is usually on the side of the operator case.
2. 2
   On-site visit and measurements. We measure the gate leaf or leaves, check the hinges and post condition, inspect the existing electrical run, and confirm the FAAC model’s torque rating matches the gate weight. No guesswork.
3. 3
   Written quote, settled before work. We give you one number that includes operator, hardware, wiring, programming, and cleanup. You approve it before we start. No surprises.
4. 4
   Installation. We mount the operator, set the arms or chain drive, run or verify the electrical supply, wire the safety devices, and program the FAAC control board to the specific gate’s weight, speed, and hold force. We use either OEM FAAC parts or a quality aftermarket equivalent only when we explain the trade-off to you first.
5. 5
   Testing. We cycle the gate in both directions with the obstacle detection tested properly, under load and in the exact sun and wind conditions of your driveway. Then we adjust final travel limits and reversing sensitivity.
6. 6
   Walkthrough and 90-Day Done Right Promise. We show you what was installed, how it works, and what to listen for. You get our written 90-Day Done Right Promise. If it’s not right, we come back and make it right. Every time.

What FAAC Gate Installation Costs in Cerritos

Every job is different, but here’s what FAAC work typically runs in Cerritos, based on what we’ve quoted over the years. These are honest ranges, not bait numbers.

• Single swing gate automation with a FAAC 400 Series: $1,900 to $3,200. Includes operator, arm kit, photocells, control board, and programming.
• Double swing gate with two FAAC operators: $3,800 to $5,600. The second leaf adds an operator, connecting hardware, and sync programming.
• Full sliding gate with a FAAC 770 or 844: $3,500 to $5,800. Includes chain drive or rack-and-pinion conversion, limit switch setup, and safety loop installation.
• FAAC operator replacement on an existing gate (labor and operator): $1,400 to $2,800 depending on model and gate size.
• New gate plus FAAC automation (full job): $5,000 to $6,800 for a steel driveway gate built to your dimensions, hung, and automated with FAAC equipment.

What moves the price: gate weight, post condition, the electrical run distance from your panel, whether we need to pour a new concrete pad, and whether safety loops need to be cut into the driveway. We’ll give you a free on-site estimate for your exact gate. Call (747) 298-3226.

Why Cerritos Homeowners Call Ironworks Gate Co. for FAAC Work

We’ve been serving Cerritos for over 42 years, since 1984. A lot of our customers have lived in the same house for twenty or thirty years. They’ve already called the cheaper guy once, and they don’t want to call anyone again.

Our technicians are background-checked and uniformed. They work in your driveway the way they’d work for their own mother. When we install a FAAC, we’re thinking about how that gate will behave in five years, not whether it works long enough to pull out of the driveway.

One detail that matters: we’re trained across nine gate-automation brands. FAAC is the one you asked about, but if a neighbor’s LiftMaster quits, or you’ve got a Mighty Mule on a side gate, a Ghost Controls on a pasture fence, or a DoorKing on the community entrance, the same tech who does your FAAC can handle those too. No second phone call, no second appointment.

And every job carries our written 90-Day Done Right Promise. If something we installed isn’t right, we fix it. No paperwork, no arguing. That’s the Keystone Standard on every job we take.

FAQs