Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFAAC Hinge & Roller Replacement: The Cerritos Owner’s Guide
We stock and install FAAC-compatible hinge and roller replacement parts for Cerritos homeowners, with most jobs completed in a single visit. An installed hinge and roller replacement on a FAAC gate typically runs between $280 and $520, depending on the model and whether one or both hinges need attention. The usual story goes like this: the gate starts dragging on the driveway, the opener sounds like it’s working harder than it should, and a quick look shows a roller that’s flattened on one side or a hinge that’s dropped half an inch. That sag is the part failing, not the motor, and it won’t fix itself.
Key takeaways:
- FAAC hinges and rollers are model-specific, not universal. We match them by measuring the old part before pulling anything apart.
- Most FAAC hinge and roller replacements in Cerritos are finished same-day, in one visit.
- You’ll get a written price before any work starts. If it’s not right within 90 days, we come back under our Done Right Promise.
Which FAAC Models This Applies To
FAAC has built several distinct lines over the years, and the hinge and roller hardware is not interchangeable between them. The 400 Series (think 402, 412, 415) swing gates use a cast hinge assembly with a greasable pin, while the 750 and 770 series slide gates run on roller carriages that ride a steel track at the base. The S800 and 844 series take a heavier roller, and many Cerritos homes with older FAAC installs from the 1990s are running the original 590 series, which has its own hinge geometry entirely. The compatibility gotcha: a roller for a 750 will physically fit into an S800 carriage and look right, but the bearing spacing is off by 4 millimeters, and you’ll chew through the new roller in six months.
We always measure the removed part with calipers and match against the FAAC spec sheet rather than trusting a “looks close enough” fit. On OEM versus aftermarket: genuine FAAC hinges and rollers are still available for most series, and for the hinge pins we lean OEM because they’re the wear point that takes all the gate weight. For rollers, quality aftermarket equivalents from U.S. manufacturers can be the smarter buy, especially on slide gates that see daily use. We’ll tell you which way we’d go and why, with the price difference laid out before you spend a dollar.
We’re an independent shop, not affiliated with FAAC, which means we stock their parts alongside LiftMaster, Mighty Mule, Ghost Controls, and the other brands our Cerritos customers run.
Signs Your FAAC Hinge & Roller Replacement Is Failing
- The gate sags toward the latch side. A hinge pin worn down by years of carrying the leaf’s weight lets the gate drop. You’ll see the gap at the bottom widen and the latch stop lining up.
- The opener struggles or trips its force setting. A collapsed roller adds drag the motor was never sized for. The FAAC control board senses the resistance and stops, which is the opener protecting itself and telling you something is wrong.
- A flat spot develops on one roller and the gate “thumps” as it travels. In Cerritos, our sandy soil works its way into roller bearings, grinds one spot flat, and the gate gets a rhythm to it: roll, roll, thump.
- You hear squealing or rasping from the hinge area during travel. By the time a hinge is dry enough to squeal, the pin and bushing are already into metal-on-metal wear. Grease now will quiet it for a week, not a season.
- The gate needs a shove to start moving. That’s usually one bad roller acting as a brake. A FAAC opener should move the gate without hesitation, and if you’re helping it, the part has already given up.
Replacement Cost & What’s Included
For Cerritos customers, a single FAAC hinge replacement runs $280 to $350 installed. A hinge pair runs $420 to $520. Roller replacement on a slide gate typically lands between $200 and $280 per roller, with most FAAC slide gates carrying anywhere from one to four rollers depending on length. Here’s how that breaks down:
- Hinge (single): $280-$350, includes the hinge, pin, grease, and labor to re-hang and align the gate leaf
- Hinge (pair): $420-$520, recommended when one is gone because the second is usually close behind
- Roller (each): $200-$280, includes the roller, bearing, hardware, and track alignment check
The price is quoted and agreed in writing before we turn a single bolt. No surprises on the invoice. Every FAAC hinge and roller replacement we do in Cerritos is covered by our 90-Day Done Right Promise: if it’s not right, we make it right, no paperwork and no arguing. Victor Salinas started this company on the idea that the finished job should do the talking, and that applies to the hinges just as much as the automation.
DIY or Call Us?
Here’s the honest split. If your FAAC gate is sagging, you can safely check the obvious things yourself: is a hinge pin visibly worn? Does a roller have a flat spot? Is the track clear of the dirt and pebbles that drift across Cerritos driveways? That’s useful information for us and costs you nothing. What we don’t recommend is pulling a hinge on a motorized gate while it’s under load. A heavy gate leaf, even a light aluminum one, carries hundreds of pounds of force when it drops. We use a gate jack to support the leaf during the swap, and we already own it. The back corner of a pickup bed isn’t a workbench, and a gate leaf that gets away from you can break a foot or a hand.
If you’re not sure whether it’s the hinge, the roller, or something in the opener, call (747) 298-3226 and describe what you’re seeing. We’ll tell you straight whether it’s worth a truck roll or whether you can squeeze another month out of the part.
FAQs
In our coastal-inland climate with sandy air and summer heat that bakes the grease out of bearings, we expect 6 to 10 years from FAAC rollers and 10 to 15 from properly greased hinges. Gates that get used six or more times a day will be on the shorter end of both ranges.
For FAAC hinges, no. Once the pin and bushing are worn enough to cause sag, there isn’t enough material left to machine or shim effectively. Rollers can sometimes be saved with a bearing replacement, but once the wheel surface is flat-spotted, it’s cheaper and more reliable to swap the assembly than to rebuild a wheel that will fail again. Call (747) 298-3226 and we’ll give you an honest read on yours.
Most single-hinge or single-roller swaps take us 45 to 90 minutes on site. A full hinge pair with gate re-alignment runs up to two hours. Nearly every job is done in one visit, and we’ll tell you the expected time when you book.
We keep the most common FAAC hinge pins, hinge assemblies, and rollers for the 400, 750/770, and S800 series stocked on our service vehicles. For older 590 series parts or unusual gate lengths, we source them from our local distributor and can usually have them within one to two business days. We’ll confirm before we schedule so you’re not waiting on a part we could have ordered first.
Contact Ironworks Gate Co.
If your FAAC gate is dragging, sagging, or fighting the opener, we’ll come out, measure the part, and give you a written price before any work starts. That’s the square deal, and we’ve been doing it that way in Cerritos for over 42 years. Call (747) 298-3226 for a free estimate. A live person answers, any hour, any day.
Written by Victor Salinas, Owner, Ironworks Gate Co. at Ironworks Gate Co., serving Cerritos and nearby areas.